AES 3075 24 VDC

Product features

Monitoring of BNS range magnetic safety sensors
2 safety contacts, STOP 0
4 Signalling outputs

Ordering data

Note (Delivery capacity)Not available!

Product type descriptionAES 3075 24 VDC

Article number (order number)101138576

EAN (European Article Number)4030661281360

eCl@ss number, version 12.027-37-18-19

eCl@ss number, version 11.027-37-18-19

eCl@ss number, version 9.027-37-18-19

ETIM number, version 7.0EC001449

ETIM number, version 6.0EC001449

Approvals - Standards

CertificatescULus

General data

StandardsBG-GS-ET-14BG-GS-ET-20EN IEC 60204-1EN IEC 60947-1EN IEC 60947-5-1EN IEC 60947-5-3EN IEC 60947-5-5EN IEC 62061EN ISO 13849-1

Housing materialGlass-fibre, reinforced thermoplastic

Gross weight379g

General data - Features

Wire breakage detection Yes

Cross-circuit detectionYes

Start inputYes

Feedback circuit Yes

Automatic reset functionYes

Integral system diagnostics, statusYes

Number of LEDs1

Number of normally closed (NC)4

Number of normally open (NO)4

Number of undelayed semi-conductor outputs with signaling function4

Number of safety contacts2

Number of signalling outputs4

Safety classification

StandardsEN IEC 61508EN ISO 13849-1

Stop-Category0

Safety classification - Relay outputs

Performance Level, up tod

Category3

PFH value1.00 x 10⁻⁷/h

Noticefor max. 50,000 switching cycles/year and max. 80% contact load

Safety Integrity Level (SIL), suitable for applications in2

Mission time20Year(s)

Mechanical data

MountingSnaps onto standard DIN rail to EN 60715

Mechanical data - Connection technique

Cable section, maximum4 mm²

NoteAll indications including the conductor ferrules.

Tightening torque of Clips0.4Nm

Terminal (mechanical)Screw terminals

Mechanical data - Dimensions

Width75mm

Height100mm

Depth110mm

Ambient conditions

IP Degree of protection of the enclosureIP40

IP Degree of protection of the installation spaceIP54

IP Degree of protection of clips or terminalsIP20

Ambient temperature+0 ... +55 °C

Storage and transport temperature-25 ... +70 °C

Resistance to vibrations10...55 Hz, Amplitude 0.35 mm, ± 15 %

Restistance to shock30 g / 11 ms

Ambient conditions - Insulation values

Rated impulse withstand voltage U_imp0.5kV

Overvoltage categoryIII

Degree of pollution2

Electrical data

Frequency range50Hz60Hz

Operating voltage24 VAC -15 % / +10 %
24 VDC -15 % / +40 %

Ripple voltage10%

Thermal test current4A

Rated operating voltage24VAC

Rated operating voltage24VDC

Rated AC voltage for controls, 50 Hz, minimum20.4VAC

Rated control voltage at AC 50 Hz, maximum26.4VAC

Rated AC voltage for controls, 60 Hz, minimum20.4VAC

Rated control voltage at AC 60 Hz, maximum26.4VAC

Rated AC voltage for controls at DC minimum20.4VDC

Rated control voltage at DC, maximum28.8VDC

Electrical power consumption8W

Contact resistance, maximum0.1Ω

Note (Contact resistance)in new state

Drop-out delay in case of power failure, typically80ms

Drop-out delay in case of emergency, typically20ms

Pull-in delay at automatic start, maximum, typically100ms

Pull-in delay at RESET, typically20ms

Electrical data - Safe relay outputs

Voltage, Utilisation category AC-15230VAC

Current, Utilisation category AC-156A

Voltage, Utilisation category DC-1324VDC

Current, Utilisation category DC-136A

Switching capacity, minimum10VDC

Switching capacity, minimum10mA

Switching capacity, maximum250VAC

Switching capacity, maximum8A

Electrical data - Digital inputs

Input signal, HIGH Signal "1"10 … 30 VDC

Input signal, LOW Signal "0"0 … 2 VDC

Conduction resistance, maximum40Ω

Electrical data - Digital Output

Voltage, Utilisation category DC-1224VDC

Current, Utilisation category DC-120.1A

Electrical data - Relay outputs (auxiliary contacts)

Switching capacity, maximum24VDC

Switching capacity, maximum2A

Electrical data - Electromagnetic compatibility (EMC)

EMC ratingEMC-Directive

Integral system diagnosis (ISD)

Note (ISD -Faults)The following faults are registered by the safety monitoring modules and indicated by ISD.

FaultsCross-wire or short-circuit monitoring of the switch connectionsFailure of door contacts to open or closeFault on the input circuits or the relay control circuits of the safety monitoring moduleInterruption of the switch connections

Other data

Note (applications)Guard systemSafety sensor

Note

Note (General)Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit.

Wiring example

Note (Wiring diagram)If less than 4 switches are connected, the unused terminals S21/S22 must be bridged before a NC contact is connected. This applies to the position of the jumpers in the safety-monitoring module with NC/NO configuration.Monitoring 4 guard door(s), each with a magnetic safety sensor of the BNS rangeStart push button: A start push button (NO) can optionally be connected into the feedback circuit. With the guard door closed, the enabling paths are then not closed until the start push button has been operated.The feedback circuit monitors the position of the positive-guided NC contacts of the contactors K3 and K4.The ISD tables (Intergral System Diagnostics) for analysis of the fault indications and their causes are shown in the appendix.The NC contacts of the external contactors must be wired in series to X1 (+) and X2.The switch (H6) connected to terminals X3 and X4 switches the enabling outputs Y14 and Y24 on and off with the guard door closed. If no switch is connected, a jumper connection must be mounted between the terminals X3 and X4.The wiring diagram is shown with guard doors closed and in de-energised condition.To secure 4 guard doors up to PL d and Category 3

The details and data referred to have been carefully checked. Images may diverge from original. Further technical data can be found in the manual. Technical amendments and errors possible.

Generated on: 08/05/2026, 20:21