.png?id=bb44e9061d048e5250879d3fc4285be0){kind=logo}
BN 120L-01Z/V 2,0M
BN 120L-01Z/V 2,0M
Downloads
- Actuation from front
- with bias magnet
- Non-contact principle
- Long life
- Thermoplastic enclosure
- Actuating distance up to 60 mm depending on actuating magnet and version
- Design Ø 10.7 mm
- with central mounting
- With pre-wired cable
Ordering data
| Product type description |
BN 120L-01Z/V 2,0M |
| Article number (order number) |
101210881 |
| EAN (European Article Number) |
4030661388458 |
| eCl@ss number, version 12.0 |
27-27-43-02 |
| eCl@ss number, version 11.0 |
27-27-01-05 |
| eCl@ss number, version 9.0 |
27-27-01-05 |
| ETIM number, version 7.0 |
EC002544 |
| ETIM number, version 6.0 |
EC002544 |
General data
| Working principle |
Magnetic drive |
| Housing construction form |
Cylinder, thread |
| Housing material |
Glass-fibre, reinforced thermoplastic |
| Gross weight |
56 g |
General data - Features
| Suitable for elevators |
Yes |
| bias magnet |
Yes |
| Number of normally closed (NC) |
1 |
Mechanical data
| Actuating panels |
front side |
| Actuating element |
Magnet |
| Mechanical life, minimum |
10,000,000 Operations |
| Actuating speed, maximum |
18 m/s |
| Mounting |
central with threated flange M12 x 1 |
| Tightening torque of nuts, maximum |
0.9 Nm |
Mechanical data - Switching distances according EN IEC 60947-5-3
| Switching distance Sn |
5 mm … 55 mm BP 10S = 5 mm 2 x BP 10S = 10 mm BP 15S = 6 mm BP 34S = 20 mm BP 20S = 15 mm BP 31S = 15 mm BP 11S = 5 mm 2 x BP 11S = 15 mm BP 12S = 10 mm 2 x BP 12S = 25 mm BP 21S = 30 mm 2 x BP 21S = 20 ... 55 mm BP 22S = 25 mm 2 x BP 22S = 15 ... 55 mm BE 20 S = 6 mm |
| Note (Switching distance Sn) |
Actuating distance up to 55 mm depending on actuating magnet and version. The specified switching distances are applicable for the actuation of individually mounted components without ferromagnetic influence. A change of the distance, either positive or negative, is possible due to ferromagnetic influences. The mutual interference between multiple actuating magnets must be observed. |
| Repeat accuracy R |
0.3 mm |
Mechanical data - Connection technique
| Length of cable |
2 m |
| Termination |
Cable |
| Wire cross-section |
0.25 mm2 |
| Wire cross-section |
23 AWG |
| Material of the Cable mantle |
LiYY |
Mechanical data - Dimensions
| Diameter of sensor |
10.7 mm |
| width across flats |
17 BK |
| Length of sensor |
102 mm |
Ambient conditions
| Degree of protection |
IP67 |
| Ambient temperature |
-25 ... +70 °C |
| Resistance to vibrations |
10 … 55 Hz, amplitude 1 mm |
| Restistance to shock |
30 g / 11 ms |
Electrical data
| Switching voltage, maximum |
200 VAC |
| Switching voltage, maximum |
200 VDC |
| Switching current, maximum |
1 A |
| Switching capacity, maximum |
30 W |
| Switching capacity, maximum |
30 VA |
| Switching element |
Opener (NC) |
Electrical data - Digital Output
| Design of control elements |
Reed contacts |
Scope of delivery
| Scope of delivery |
Actuator must be ordered separately. |
Accessory
| Recommendation (actuator) |
BP 10 S 2x BP 10 S BP 15 S BP 34 S BP 20 S BP 31 S BP 11 S 2x BP 11 S BP 12 S 2x BP 12S BP 21 S 2x BP 21 S BP 22 S 2x BP 22 S BE 20 S |
| Recommendation (actuator, lift switchgear) |
BP 10 2 x BP 10 BP 15 BP 34 |
Note
| Note (General) |
The opening and closing functions depend on the direction of actuation, the actuating magnets and the polarity of the actuating magnets. When the switches and actuators come together, the colours must coincide: Red (S) to red (S) and green (N) to green (N). This does not apply to the bistable contact. The switch is to be mounted on iron with a non-magnetic layer of at least 20 mm. |
Language filter
Datasheet
Mounting and wiring instructions
EC Declaration of conformity
Info
Download the latest version of Adobe Reader
Product picture (catalogue individual photo)
Dimensional drawing basic component
Switch travel diagram
Contact closed
Contact open
Setting range
Latching point
Positive opening path/angleDiagram
Monitoring the interlock to EN ISO 14119
Positive break NC contact
Actuated
Not actuated
Normally-open contact
Normally-closed contact
Characteristic curve
101060163 BP 15
- thermoplastic enclosure
- N-pole marked green
- S-pole marked red
- Suitable for mounting on ferrous material with a distance of 18 mm
101060165 BP 15/2
- Unenclosed
- Polarity stamped in
- Suitable for mounting on ferrous material with a distance of 18 mm
101057531 BP 10
- Unenclosed
- Colour coding of poles by lables
101057553 BP 34
- thermoplastic enclosure
- S-pole marked red
- N-pole marked green
- Suitable for mounting on ferrous material with a distance of 25 mm
K.A. Schmersal GmbH & Co. KG, Möddinghofe 30, 42279 Wuppertal
The details and data referred to have been carefully checked. Images may diverge from original. Further technical data can be found in the manual. Technical amendments and errors possible.
Generated on: 24/11/2024, 12:53