Not available!

AES 2336 UE: 24...230V AC/DC

101181678

4030661323091

27-37-18-19

27-37-18-19

27-37-18-19

EC001449

EC001449

31.12.2024

cULus

BG-GS-ET-14

BG-GS-ET-20

EN IEC 62061

EN IEC 60947-5-1

EN IEC 60947-5-3

EN IEC 60947-5-5

EN IEC 61508

EN IEC 60204-1

EN IEC 60947-1

EN 60068-2-3

BG-GS-ET-14

グラスファイバー強化熱可塑性樹脂

300 g

Yes

Yes

Yes

Yes

Yes

Yes

Yes

1

2

1

2

3

2

EN ISO 13849-1

EN IEC 61508

0

d

3

1.00 x 10⁻⁷ /h

for max. 50,000 switching cycles/year and max. 80% contact load

2

20 年

20,000,000 操作

EN 60715に基づくDINレールにワンタッチ取り付け

IEC/EN 60947-1

単線 / 撚線

ネジ端子 M20 x 1.5

0.25 mm²

2.5 mm²

0.6 Nm

45 mm

100 mm

121 mm

IP40

IP54

IP20

+0 ... +55 °C

-25 ... +70 °C

10 ~ 55 Hz、振幅 0.35 mm、± 15 %

30 g / 11 ms

4 kV

III

2

50 Hz

60 Hz

AC

DC

6 A

24 ... 230 VAC
24 ... 230 VDC

20.4 VAC

253 VAC

20.4 VAC

253 VAC

20.4 VDC

253 VDC

5 W

0.1 Ω

新しい状態で

80 ms

20 ms

100 ms

20 ms

Ag-Ni 10および0.2 µm 金メッキ

230 VAC

3 A

24 VDC

2 A

10 VDC

10 mA

250 VAC

8 A

10 … 30 VDC

0 … 2 VDC

40 Ω

24 VDC

0.1 A

24 VDC

2 A

EMC-Directive

The following faults are registered by the safety monitoring modules and indicated by ISD.

Failure of the safety relay to pull-in or drop-out

Failure of door contacts to open or close

Cross-wire or short-circuit monitoring of the switch connections

Interruption of the switch connections

Fault on the input circuits or the relay control circuits of the safety monitoring module

Failure of or functional fault on the safety relay

セーフティセンサー

ガードシステム

Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit.

The wiring diagram is shown with guard doors closed and in de-energised condition.

To secure a guard door up to PL d and Category 3

The ISD tables (Intergral System Diagnostics) for analysis of the fault indications and their causes are shown in the appendix.

Start push button: A start push button (NO) can optionally be connected into the feedback circuit. With the guard door closed, the enabling paths are then not closed until the start push button has been operated.

Modification for 2 NC contacts: The safety monitoring module can be modified to monitor two NC contacts by bridging the terminals X3 and X4. In this configuration, the short-circuit detection becomes inoperative.

Inversion of the output function: By establishing a bridge between X5 and X6, the output function of the additional outputs can be altered. This control can also be realised when e.g. a PLC is running (24 VDC at terminal X6).

Expansion of the enable delay time. The enable delay time can be increased from X7 s to X8 s by mounting a jumper connection between the terminals 0,1 and 1.

Monitoring a guard door using 2 position switches with safety function.

The NC contact A must have positive break when the guard door is opened.

Category 3 to ISO 13849-1 can also be achieved using only one safety switch with one NO and one NC contact. Exclusion of faults due to breakage or loosening of the actuating element or the actuating head as well as releasing, dismantling.

The feedback circuit monitors the position of the positive-guided NC contacts of the contactors K3 and K4.

If neither start button nor feedback circuit are connected, a jumper connection must be mounted between X1 and X2.